The article listed below in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is quite engaging. Check it out for yourself and decide what you think of it.
Mounting a bath tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard job. If the old bathtub is easily available, the project can relocate rapidly; if you have to open a wall to remove the old tub and position the new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Ensure you have qualified yourself for the work and also fit attempting it. Instead of hiring a contractor to take control of a halfway-completed task, it is much better to think about employing one before you start. Opportunities are you may need a professional plumber to make tube links.
This write-up will certainly assist you install a brand-new bath tub in your restroom if you have currently acquired a brand-new tub and also do not need to change the setup of your previous water system pipes.
Your tools and also product checklist need to consist of the following:
- New Tub
- Hammer
- Pipe Wrenches
- Prybar
- Shatterproof glass
- Level
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Blade
- Tape Measure
- Pipeline Caps
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers are in location in between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the bath tub in the called for position. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also check all joints and new pipework for leaks and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the tub has been used at the very least when as this will certainly settle it into its last placement.
Getting ready for the Setup
Firstly, the sustaining structure supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to problems with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section about How to Install a Bathtub Yourself. Thanks for finding the time to browse our post. Enjoyed our entry? Please share it. Let other people discover it. Thanks so much for your time invested reading it.
Get A Free Quote
Comments on “Do It Yourself Bathtub Setup.”